|
  |
INSERT BEVEL TRIM |
|
| New design with small, 2-sided carbide insert knives. The ideal router bit for both routers and hand-held laminate trimmers with 1/4" shank. New design breakthrough allows us to manufacture this insert bit for practically the same cost as regular brazed router bit. |
 |
| |
|
|
|
|
|
|
Replacement Knives |
|
|
| Tool No. |
D |
B |
d |
L |
Price |
|
(min. order 10ea,) |
Price |
|
| RC-2000 |
1/2 |
8MM (5/16) |
1/4 |
2-1/4 |
35.69 |
|
RCK-8 |
1.59 |
|
| |
Replacement Knives |
|
|
| Tool No. |
D |
B |
d |
L |
Price |
|
(min. order 10ea.) |
Price |
|
| RC-1000 |
3/4 |
15/32 |
1/4 |
2-1/8 |
61.59 |
|
AMA-12 |
2.67 |
|
| RC-1002 |
3/4 |
1-1/8 |
1/4 |
2-3/4 |
71.01 |
|
ICK-30 |
4.23 |
|
| RC-1004 |
3/4 |
1-1/8 |
1/2 |
3-1/4 |
71.01 |
|
ICK-30 |
4.23 |
|
 |
Note: All bevel trim bits have four cutting sides per knife. Torx® key is included. Replacement bearing for RC-1014 use #47701. All others use #47712 bearing. Replacement screws #67115. |
 |
| |
|
|
|
|
|
|
|
Replacement Knives |
|
|
| Tool No. |
a° |
D |
B |
d |
L |
Price |
|
(min. order 10ea,) |
Price |
|
| RC-1008 |
15° |
13/16 |
7/16 |
1/4 |
2-1/4 |
71.01 |
|
AMA-12 |
2.67 |
|
| RC-1010 |
25° |
31/32 |
7/16 |
1/4 |
2-1/4 |
71.01 |
|
AMA-12 |
2.67 |
|
| RC-1012 |
30° |
1 |
7/16 |
1/4 |
2-1/4 |
71.01 |
|
AMA-12 |
2.67 |
|
| RC-1014 |
45° |
1-1/16 |
7/16 |
1/4 |
2-1/4 |
71.01 |
|
AMA-12 |
2.67 |
|
 |
| Our patented 'No-File'Bit eliminates hand filing of laminates that normally follows trimming. These specially designed tools will flush trim the laminate and "break" the sharp edge all in one pass. |
| Note: #47154 is for laminates .025-.038 thick (.4mm radius), #'s 47150-47152 are for laminates .042-.052 thick (1.5mm radius). Replacement bearing #47704 (3/8" diameter). |
 |
| 2 Flute |
| Tool No. |
D |
B |
R |
d |
L |
Price |
|
| 47150 |
1/2 |
3/8 |
.059 (1.5MM) |
1/4 |
1-7/8 |
21.32 |
|
| 47152 |
1/2 |
3/8 |
.059 (1.5MM) |
1/2 |
2-1/8 |
21.81 |
|
| 47154 |
1/2 |
3/8 |
.015 (.4MM) |
1/4 |
1-7/8 |
20.80 |
|
 |
Used for preliminary laminate trimming, leaving a small overhang. Reduces chipping of material caused by excessive feed-rate or vibration. Final pass can be achieved using a standard trim bit, or 'No-File' bit.
Replacement bearing #47718. |
 |
| Tool No. |
D |
B |
d |
L |
A |
Price |
|
| 47190 |
3/8 |
1/2 |
1/4 |
2 |
1/8 |
17.19 |
|
| 47192 |
1/2 |
1/2 |
1/4 |
2 |
1/16 |
16.77 |
|
| 47194 |
1/2 |
1/2 |
1/2 |
2-5/8 |
1/16 |
17.19 |
|
 |
| Double application in a single pass: flush trim and 'V' Groove on face frame. |
 |
| Tool No. |
D |
B |
d |
L |
Price |
|
| 47160 |
5/8 |
1 |
1/4 |
2-1/2 |
23.14 |
|
| 47162 |
5/8 |
1 |
1/2 |
3 |
24.86 |
|
|
Products shown in Bold indicate most popular items.
|
© 2003 Amana Tool Corporation. All Rights Reserved
|
|
