A.G.E. SERIES
FOR WOOD
ATB (Alternate Top Bevel) moderate angle
Application: Designed to rip along the grain in wood or man-made materials. For use on table saws or gange-rip saws. Moderate angle ATB grind for increased feed rates.
Tool No. Price   Dia.
Teeth
 Kerf Plate Bore
MD10-240 35.97 10" 24 .126 .087 5/8"
MD12-280 44.23 12" 28 .126 .087 1"
MD14-360 53.01 14" 36 .138 .100 1"



ATB (Alternate Top Bevel)
Application: Medium tooth count to cover a wide range of cuts: rip, bias, and crosscut.
Tool No. Price   Dia.
Teeth
 Kerf Plate Bore
MD10-400 42.05 10" 40 .126 .087 5/8"
MD12-480 46.44 12" 48 .126 .087 1"
MD14-600 73.12 14" 60 .155 .110 1"



ATB (Alternate Top Bevel)
Application: Designed for smooth cross cuts in all natural wood. These blades are fine and extra fine cuts.
Tool No. Price   Dia.
Teeth
 Kerf Plate Bore
MD10-600 46.54 10" 40 .126 .087 5/8"
MD10-800 60.05 12" 48 .126 .087 5/8"
MD12-600 56.13 12" 60 .126 .087 1"
MD12-720 61.67 12" 72 .126 .087 1"
MD12-970 Call Us 12" 96 .126 .087 1"
MD14-800 94.29 14" 80 .150 .110 1"



TCG (Triple Chip Grind) followed by Flat Raker
Application: Designed for cross-cuts and trim work on plywood, composite materials and single sided laminated material. Higher tooth count yields a finer cut.
Tool No. Price   Dia.
Teeth
 Kerf Plate Bore
MD10-601 48.08 10" 60 .126 .087 5/8"
MD10-801 60.98 10" 80 .126 .087 5/8"
MD12-721 66.03 12" 72 .126 .087 1"
MD12-961 80.81 12" 100 .138 .098 1"
MD14-801 103.97 14" 80 .150 .110 1"



Combination 4 + 1 Alternate Top Bevel Teeth followed by one Raker Tooth, and then an "open" gullet for chip clearance.
Application: This blade is specially designed for ripping and cross-cutting in solid wood, plywood, and particle boards. The most widely accepted geometry for a wood blade with universal application.
Tool No. Price   Dia.
Teeth
 Kerf Plate Bore
MD10-500 47.14 10" 50 .126 .087 5.8"



H-ATB (High or Acute Angle Alternate Top Bevel)
Application: For fine "chip-free" cuts on all double-sided laminated material, melamine, formica, veneer, etc. On table saws without scoring unit, vertical panel sizing saws, radial arm saws, miter and chop saws. Extra hard sub-micro grain carbide tips for long life.
Tool No. Price   Dia.
Teeth
 Kerf Plate Bore
MD10-803 72.56 10" 80 .126 .087 5/8"
MD12-963 87.09 12" 100 .126 .087 1"



4 ATB + R (4 Alternate Top Bevel followed by 1 Raker Tooth)
Application: For glass smooth miter cuts on moulding material(s). For single and double miter box machines. Special grind, minimal run-out and tight side clearances all combine to yield perfect gap-free miters.
Tool No. Price   Dia.
Teeth
 Kerf Plate Bore
MD10-806 61.35 10" 80 .115 .087 5/8"
MD12-106 80.81 12" 100 .126 .098 1"
MD12-106-5/8 80.81 12" 100 .126 .098 5/8"


NOTE: Due to the rough applications for which these blades may be used, they are not guaranteed.
*WARNING: Demolition blade is not to be used on multi-purpose cutoff saws or gas power saws, unless saw has a guard that covers both the upper half and the lower half of the blade completely. The guard must extend to the lowest point of the cutting teeth on the bottom of the blade. Consult owners manual of the saw & follow all instructions and safety procedures - including wearing safety goggles at all times while working with this blade.

© 2003 Amana Tool Corporation. All Rights Reserved

Connecticut Saw & Tool
140 Avon Street, Stratford, CT 06615
Phone: (800) 404-1220 Fax: (203) 378-7346 EMail: Info@CTSaw.com